Technical
Information Bulletin
Tramfloc® 1101 ANTIFOAM and DEFOAMER
DESCRIPTION
TRAMFLOC® 1101 ANTIFOAM and DEFOAMER
is a ten percent {10%} active, silicone emulsion
with excellent stability and can be added directly
to the foaming system.
TYPICAL PROPERTIES
Actives: 10% Silica-Filled Polydimethylsiloxane
Appearance: Creamy White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH: 5.5
TRAMFLOC® 1101 ANTIFOAM and DEFOAMER
is dispersible from room temperature to just below
the boil. It is effective at very low concentrations.
Ten to fifty {10-50} ppm is a good starting point.
The concentration can be adjusted to give the most
economical concentration.
TRAMFLOC® 1101 ANTIFOAM and DEFOAMER
is stable in acid, alkaline or neutral systems.
Some of the recommended uses are in textiles, paper
coatings, size mixes, printing ink manufacturing,
wastewater ponds, and sewage systems.
TRAMFLOC® 1101 ANTIFOAM and DEFOAMER
is a very stable product, yet it releases its silicone
very rapidly when added to the foaming media. As
with most defoamers, best results are obtained by
adding it to the system before foaming starts.
FDA STATUS
TRAMFLOC® 1101 ANTIFOAM and DEFOAMER
is manufactured in compliance with the regulations
of the Food and Drug Administration as cited in
21 CFR, Section 176.200 (defoaming agents used in
coatings) and Section 176.210 (defoaming agents
used in the manufacture of paper and paperboard).
EPA STATUS
The ingredients in TRAMFLOC® 1101
ANTIFOAM and DEFOAMER are in compliance with 40
CFR 180.1001(d), exempted from the requirements
of a tolerance for application on growing crops.
STORAGE
TRAMFLOC® 1101 ANTIFOAM and DEFOAMER
should remain shelf stable for up to six {6} months
in its original container. To avoid freezing, store
above 40°F. Product may separate upon freezing.
The above data is based upon information Tramfloc®,
Inc. believes reliable and is supplied for informational
purposes only. Tramfloc®, Inc. disclaims
any liability for damage or injury which results
from the use of the above data and nothing contained
herein shall constitute a guarantee, warranty (including
warranty of merchantability or fitness for a particular
purpose) or representation (including freedom from
patent liability) by Tramfloc®,
Inc. with respect to the accuracy or completeness
of the data, the product described, or their use
for any specific purpose even if that purpose is
known to Tramfloc®, Inc. The final
determination of the suitability of the information,
the manner of use of the information or product
and potential infringement of patents is the sole
responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc® 1102 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc® 1102 ANTIFOAM and DEFOAMER
is a water-dilutable, 10% active, silicone ANTIFOAM
and DEFOAMER. It has been designed to control foam
in water-based food and chemical processes. Tramfloc®
1102 is a long-lasting antifoam that is nearly inert.
TYPICAL PROPERTIES
Actives: 10% Silica-Filled Polydimethylsiloxane
Appearance: Cream White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH.: 4.0 To 5.0
FDA STATUS
Tramfloc® 1102 is manufactured in
compliance with the regulations of the Food and
Drug Administration as cited in 21 CFR 173.340,
defoaming agents used in processing foods. Use quantities
should be based upon the limitations as prescribed
by the FDA.
USDA STATUS
Tramfloc® 1102 is chemically acceptable
by the USDA for certain meat and poultry applications.
For specific applications and/or limitations, please
contact Tramfloc®, Inc.
EPA STATUS
40 CFR 180.1001©, exempted from the requirement
of a tolerance for application on growing crops.
Tramfloc® 1102 ANTIFOAM and DEFOAMER
USES
Tramfloc® 1102 is compatible in
most wet processing applications, but it is advisable
to pre-check each application. It is most effective
when used to prevent foam formation; therefore,
it is best to add Tramfloc® 1102
to the system before foaming starts. Tramfloc®
1102 concentration should be adjusted for each foaming
system to determine the optimum concentration to
use. It is suggested that the concentration can
be decreased to establish the most economical quantity.
Dilutions should be made by first charging water
and then adding Tramfloc® 1102 .
Mechanical mixing is required to ensure even distribution.
STORAGE
Tramfloc® 1102 should remain shelf-stable
for up to 12 months in its original, sealed container.
To avoid freezing, store above 40°F. Product may
separate upon freezing.
The above data is based upon information Tramfloc®,
Inc. believes reliable and is supplied for informational
purposes only. Tramfloc®, Inc. disclaims
any liability for damage or injury which results
from the use of the above data and nothing contained
herein shall constitute a guarantee, warranty (including
warranty of merchantability or fitness for a particular
purpose) or representation (including freedom from
patent liability) by Tramfloc®,
Inc. with respect to the accuracy or completeness
of the data, the product described, or their use
for any specific purpose even if that purpose is
known to Tramfloc®, Inc. The final
determination of the suitability of the information,
the manner of use of the information or product
and potential infringement of patents is the sole
responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc® 1103 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc® 1103 Antifoam is a compound
based on dimethyl polysiloxane fluid, developed
specifically for the defoaming of aqueous or anhydrous
media. It is a product regularly used in numerous
industries, such as the chemical, rubber, paper,
painting, textile and agrichemical industries.
FEATURES
Tramfloc® 1103 Antifoam presents
a number of advantages, among which are the following:
* Excellent efficacy: Tramfloc®
1103 Antifoam is effective in a diluted form of
between 1 and 200 parts per million of foaming medium.
* Chemically inert: Tramfloc® 1103
Antifoam is chemically inert in relation to the
material to be defoamed. It will not modify the
typical properties of any foaming media.
APPLICATION
Tramfloc® 1103 Antifoam may be used
in many varied applications, as follows:
TYPICAL PROPERTIES
Chemical Nature: Compound Based On Dimethyl Polysiloxane
Fluid
Appearance: Viscous, Homogenous Liquid
Color: Clear Grey; Translucent
Active Ingredients (%): 100
Diluents: Aromatic, Aliphatic, And Chlorinated Hydrocarbons
Specific Gravity @ 25°C: 1.0
Emulsifiers: None
EPA STATUS
The ingredients in Tramfloc® 1103
are listed in EPA Regulations, 40 CFR 180.1001(d),
exempted from the requirements of a tolerance for
application on growing crops.
PACKAGING
Tramfloc® 1103 Antifoam is available
in 460-pound drums and bulk.
STORAGE
Tramfloc® 1103 Antifoam may be kept
in its original, unopened container for twelve (12)
months at room temperature.
The above data is based upon information Tramfloc®,
Inc. believes reliable and is supplied for informational
purposes only. Tramfloc®, Inc. disclaims
any liability for damage or injury which results
from the use of the above data and nothing contained
herein shall constitute a guarantee, warranty (including
warranty of merchantability or fitness for a particular
purpose) or representation (including freedom from
patent liability) by Tramfloc®,
Inc. with respect to the accuracy or completeness
of the data, the product described, or their use
for any specific purpose even if that purpose is
known to Tramfloc®, Inc. The final
determination of the suitability of the information,
the manner of use of the information or product
and potential infringement of patents is the sole
responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc®
1104 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc® 1104 is a silicone-organic
antifoam compound that is readily dispersible in
water. It is for use in controlling foam in industrial
aqueous systems over wide pH and temperature ranges.
Tramfloc® 1104 provides a very convenient
form of silicone antifoam compound that can be formulated
into aqueous-based antifoams. Antifoams formulated
with Tramfloc® 1104 can rinse free
from substrates by flushing with water at room temperatures.
Tramfloc® 1104 is manufactured in
accordance with the Regulations of the Food and
Drug Administration as described in 21 CFR, Section
176.210. The ingredients of Tramfloc®
1104 are in compliance with the EPA under 40 CFR
180.1001(c), "exempted from the requirements of
a tolerance for application on growing crops or
to raw agricultural commodities after harvest."
TYPICAL PROPERTIES
Appearance: Milky, White Liquid
Viscosity @ 25°C: 6,000 cps
Actives: 100%
Flash Point {cc}: Above 250°F
USES OF TRAMFLOC® 1104 ANTIFOAM
Tramfloc® 1104 has been especially
prepared for the formulators of aqueous-based antifoams.
It is easily extended with cool water to active
levels as low as 5% or as high as 40%. The general
procedure is to mix Tramfloc® 1104
into thickened water at room temperature. Without
thickener, water emulsions are not stable. Thickened
emulsions of Tramfloc® 1104 can
be stable for prolonged periods, depending on the
type and concentration of the thickener. Synthetic
thickeners, such as Carbopol 990 (B. F. Goodrich)
or Acrysol ASE-60 (Rohm & Haas), can be used. Preservatives
may be used in the finished emulsions to retard
microorganism growth.
STORAGE
Tramfloc® 1104 has a shelf life
of up to 12 months in the original, unopened container.
It is possible that may separate slightly during
prolonged storage, especially under warm conditions.
If separation does occur, mechanical mixing will
restore it to original condition and efficiency.
It will become much thicker as the temperature is
decreased. If stored at low temperature, warm to
above 15°C (60°F) prior to use.
The above data is based upon information Tramfloc®,
Inc. believes reliable and is supplied for informational
purposes only. Tramfloc®, Inc. disclaims
any liability for damage or injury which results
from the use of the above data and nothing contained
herein shall constitute a guarantee, warranty (including
warranty of merchantability or fitness for a particular
purpose) or representation (including freedom from
patent liability) by Tramfloc®,
Inc. with respect to the accuracy or completeness
of the data, the product described, or their use
for any specific purpose even if that purpose is
known to Tramfloc®, Inc. The final
determination of the suitability of the information,
the manner of use of the information or product
and potential infringement of patents is the sole
responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc®
1105 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc® 1105 is a silicone-organic
antifoam compound that is readily dispersible in
water. It is for use in controlling foam in paper-making,
aqueous systems over wide pH and temperature ranges.
Tramfloc® 1105 provides a very convenient
form of silicone antifoam compound that can be formulated
into aqueous-based antifoams. Antifoams formulated
with Tramfloc® 1105 are high temperature
and high pH durable, providing improved "holdout"
compared to other antifoams. Tramfloc®
1105 is manufactured in accordance with the Regulations
of the Food and Drug Administration as described
in 21 CFR, Section 176.210.
TYPICAL PROPERTIES
Appearance: Milky, White Liquid
Viscosity @ 25°C: 2,300 cps
Actives: 100%
Flash Point {cc}: Above 250°F
USES OF TRAMFLOC® 1105
Tramfloc® 1105 has been especially
prepared for the formulators of aqueous-based antifoams.
It is easily extended with cool water to active
levels as low as 2% or as high as 40%. The general
procedure is to mix Tramfloc® 1105
into thickened at room temperature. Without thickener,
water emulsions are not stable. Thickened emulsions
of Tramfloc® 1105 can be stable
for prolonged periods, depending on the type and
concentration of the thickener. Synthetic thickeners
such as Kelzan S {Kelco Division of Merck} or Acrysol
ASE-60 {Rohm & Haas} can be used. Preservatives
may be used in the finished emulsions to retard
microorganism growth.
STORAGE
Tramfloc® 1105 has a shelf life
of up to 12 months in the original, unopened container.
It is possible that Tramfloc® 1105
may separate slightly during prolonged storage,
especially under warm conditions. If separation
does occur, agitation will restore it to original
condition and efficiency. It will become much thicker
as the temperature is decreased. If stored at low
temperature, warm to above 15°C (60°F) prior to
use.
The above data is based upon information Tramfloc®,
Inc. believes reliable and is supplied for informational
purposes only. Tramfloc®, Inc. disclaims
any liability for damage or injury which results
from the use of the above data and nothing contained
herein shall constitute a guarantee, warranty (including
warranty of merchantability or fitness for a particular
purpose) or representation (including freedom from
patent liability) by Tramfloc®,
Inc. with respect to the accuracy or completeness
of the data, the product described, or their use
for any specific purpose even if that purpose is
known to Tramfloc®, Inc. The final
determination of the suitability of the information,
the manner of use of the information or product
and potential infringement of patents is the sole
responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc®
1106 ANTIFOAM and DEFOAMER
DESCRIPTION:
Tramfloc® 1106 Antifoam is a compound
based on dimethyl polysiloxane fluid, developed
specifically for defoaming over wide pH and temperature
ranges. Tramfloc® 1106 Antifoam
is ultimately formulated for industrial use only.
Tramfloc® 1106 is manufactured in
accordance with the Regulations of the United States
Food and Drug Administration as described in 21
CFR Section 176.210, "defoaming agents used in the
manufacture of paper and paperboard."
FEATURES
Tramfloc® 1106 Antifoam presents
a number of advantages, among which are the following:
* Ease of use:
Tramfloc® 1106 Antifoam may be applied
neat or diluted in a solvent or in a portion of
the foaming medium.
* Excellent efficiency.
* Chemically inert.
Tramfloc® 1106 Antifoam is chemically
inert in relation to the material to be defoamed.
It will not modify the typical properties of any
foaming media.
TYPICAL PROPERTIES
Chemical Nature: Compound Based On Dimethyl Polysiloxane
Fluid
Appearance: Viscous, Homogenous Liquid
PACKAGING
Tramfloc® 1106 Antifoam is available
in 460-pound drums and bulk.
STORAGE
Tramfloc® 1106 Antifoam may be kept
in its original, unopened container for twelve (12)
months at room temperature.
The above data is based upon information Tramfloc®,
Inc. believes reliable and is supplied for informational
purposes only. Tramfloc®, Inc. disclaims
any liability for damage or injury which results
from the use of the above data and nothing contained
herein shall constitute a guarantee, warranty (including
warranty of merchantability or fitness for a particular
purpose) or representation (including freedom from
patent liability) by Tramfloc®,
Inc. with respect to the accuracy or completeness
of the data, the product described, or their use
for any specific purpose even if that purpose is
known to Tramfloc®, Inc. The final
determination of the suitability of the information,
the manner of use of the information or product
and potential infringement of patents is the sole
responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc®
1107 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc® 1107 is an excellent ANTIFOAM
and DEFOAMER emulsion based upon a unique organic-polysiloxane
compound. It is used for controlling foam in aqueous
systems. Tramfloc® 1107 is compatible
in most systems where foaming is a problem. It may
be used in hot foaming systems {up to 180oF} and
remain stable. After its use in high temperature
environments, Tramfloc® 1107 can
be rinsed away without oil scum deposits. Tramfloc®
1107 is stable in acid, alkaline, or neutral systems.
TYPICAL PROPERTIES
Appearance: Milky, White Liquid
Specific Gravity @ 20°C: 1.0
Viscosity {20°C} 1,000 -3,500 cps
Defoamer Actives: 20%
pH: 6-8
USES
Use levels of Tramfloc® 1107 depend
upon the nature and severity of the foaming. Normally
in latex systems, it should be evaluated initially
as a pound-for-pound replacement for conventional
defoamers. Dilutions of Tramfloc®
1107 should be made by first charging the water
and then adding Tramfloc® 1107.
Mechanical mixing is required to ensure even distribution.
Water dilutions below 5% may have limited shelf
stability.
FDA STATUS
Tramfloc® 1107 is manufactured in
compliance with the Regulations of the Food and
Drug Administration as cited in 21 CFR, Section
176.210 (defoaming agents used in the manufacture
of paper and paperboard.)
FPA STATUS
The ingredients of Tramfloc® 1107
are listed in EPA Regulations, 40 CFR 180.1001(d),
exempted from the requirements of a tolerance for
application on growing crops.
STORAGE
Tramfloc® 1107 should remain shelf
stable for up to 12 months in its original, sealed
container. To avoid freezing, store above 40oF.
Product may separate upon freezing.
The above data is based upon information Tramfloc®,
Inc. believes reliable and is supplied for informational
purposes only. Tramfloc®, Inc. disclaims
any liability for damage or injury which results
from the use of the above data and nothing contained
herein shall constitute a guarantee, warranty (including
warranty of merchantability or fitness for a particular
purpose) or representation (including freedom from
patent liability) by Tramfloc®,
Inc. with respect to the accuracy or completeness
of the data, the product described, or their use
for any specific purpose even if that purpose is
known to Tramfloc®, Inc. The final
determination of the suitability of the information,
the manner of use of the information or product
and potential infringement of patents is the sole
responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc®
1108 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc® 1108 is a water-dilutable,
20% active, silicone ANTIFOAM and DEFOAMER. It has
been designed to control foam in water-based food
and chemical processes. Tramfloc®
1108 is a long-lasting antifoam that is nearly inert.
TYPICAL PROPERTIES
Atives: 20% Silica-Filled Polydimethylsiloxane
Appearance: Cream White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH: 4.5 to 6.0
FDA STATUS
Tramfloc® 1108 is manufactured in
compliance with the regulations of the Food and
Drug Administration as cited in 21 CFR 173.340,
defoaming agents used in processing foods. Use quantities
should be based upon the limitations as prescribed
by the FDA.
USDA STATUS
Tramfloc® 1108 is chemically acceptable
by the USDA for certain meat and poultry applications.
For specific applications and/or limitations, please
contact Tramfloc®, Inc.
EPA STATUS
The ingredients in Tramfloc® 1108
are listed in EPA Regulations, 40 CFR 180.1001(d),
exempted from the requirements of a tolerance for
application on growing crops for pesticide applications.
USES
Tramfloc® 1108 is compatible in
most wet processing applications, but it is advisable
to pre-check each application. It is most effective
when used to prevent foam formation; therefore,
it is best to add Tramfloc® 1108
to the system before foaming starts. Tramfloc®
1108 concentration should be adjusted for each foaming
system to determine the optimum concentration to
use. It is suggested that the concentration can
be decreased to establish the most economical quantity.
Dilutions should be made by first charging water
and then adding Tramfloc® 1108.
Mechanical mixing is required to ensure even distribution.
STORAGE
Tramfloc® 1108 has a shelf life
of up to six 12 months in its original, unopened
container.
The above data is based upon information Tramfloc®,
Inc. believes reliable and is supplied for informational
purposes only. Tramfloc®, Inc. disclaims
any liability for damage or injury which results
from the use of the above data and nothing contained
herein shall constitute a guarantee, warranty (including
warranty of merchantability or fitness for a particular
purpose) or representation (including freedom from
patent liability) by Tramfloc®,
Inc. with respect to the accuracy or completeness
of the data, the product described, or their use
for any specific purpose even if that purpose is
known to Tramfloc®, Inc. The final
determination of the suitability of the information,
the manner of use of the information or product
and potential infringement of patents is the sole
responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc®
1109 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc® 1109 is a water-dilutable,
30% active, silicone ANTIFOAM and DEFOAMER. It has
been designed to control foam in water-based food
and chemical processes. Tramfloc®
1109 is a long-lasting antifoam that is nearly inert.
TYPICAL PROPERTIES
Actives:30% Silica-Filled Polydimethylsiloxane
Appearance: Cream White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH: 5.5
FDA STATUS
Tramfloc® 1109 is manufactured in
compliance with the regulations of the Food and
Drug Administration as cited in 21 CFR 173.340,
defoaming agents used in processing foods. Use quantities
should be based upon the limitations as prescribed
by the FDA.
USDA STATUS
Tramfloc® 1109 is chemically acceptable
by the USDA for certain meat and poultry processing
applications. For specific applications and/or limitations,
please contact Tramfloc®, Inc.
EPA STATUS
The ingredients in Tramfloc® 1109
are listed in EPA Regulations, 40 CFR 180.1001(d),
exempted from the requirements of a tolerance for
application on growing crops.
USES
Tramfloc® 1109 is compatible in
most wet processing applications, but it is advisable
to pre-check each application. It is most effective
when used to prevent foam formation; therefore,
it is best to add Tramfloc® 1109
to the system before foaming starts. Tramfloc®
1109 concentration should be adjusted for each foaming
system to determine the optimum concentration to
use. It is suggested that the concentration can
be decreased to establish the most economical quantity.
Dilutions should be made by first charging water
and then adding Tramfloc® 1109.
Mechanical mixing is required to ensure even distribution.
STORAGE
Tramfloc® 1109 should remain shelf
stable for up to 12 months in its original, sealed
container. To avoid freezing, store above 40 deg.
F. Product may separate upon freezing.
Return To Listing
Technical Information Bulletin
Tramfloc®
1110 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc® 1110 ANTIFOAM and DEFOAMER
is a ten percent {10%} active, silicone emulsion
with excellent stability and can be added directly
to the foaming system.
TYPICAL PROPERTIES
Actives: 10% Silica-Filled Polydimethylsiloxane
Appearance: Cream White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH: 5.5
Tramfloc® 1110 ANTIFOAM and DEFOAMER
is dispersible from room temperature to just below
the boil. It is effective at very low concentrations.
Ten to fifty {10-50} ppm is a good starting point.
The concentration can be adjusted to give the most
economical concentration. Tramfloc®
1110 ANTIFOAM and DEFOAMER is stable in acid, alkaline
or neutral systems. Some of the recommended uses
are in textiles, paper coatings, size mixes, printing
ink manufacturing, wastewater ponds, and sewage
systems. Tramfloc® 1110 ANTIFOAM
and DEFOAMER is a very stable product, yet it releases
its silicone very rapidly when added to the foaming
media. As with most defoamers, best results are
obtained by adding it to the system before foaming
starts.
FDA STATUS
Tramfloc® 1110 is manufactured in
compliance with the regulations of the Food and
Drug Administration as cited in 21 CFR, Section
176.200 (defoaming agents used in coatings) and
Section 176.210 (defoaming agents used in the manufacture
of paper and paperboard).
EPA STATUS
The ingredients in Tramfloc® 1110
are in compliance with 40 CFR 180.1001(d), exempted
from the requirements of a tolerance for application
on growing crops.
STORAGE
Tramfloc® 1110 should remain shelf
stable for up to 12 months in its original container.
To avoid freezing, store above 40oF. Product may
separate upon freezing.
The above data is based upon information Tramfloc®,
Inc. believes reliable and is supplied for informational
purposes only. Tramfloc®, Inc. disclaims
any liability for damage or injury which results
from the use of the above data and nothing contained
herein shall constitute a guarantee, warranty (including
warranty of merchantability or fitness for a particular
purpose) or representation (including freedom from
patent liability) by Tramfloc®,
Inc. with respect to the accuracy or completeness
of the data, the product described, or their use
for any specific purpose even if that purpose is
known to Tramfloc®, Inc. The final
determination of the suitability of the information,
the manner of use of the information or product
and potential infringement of patents is the sole
responsibility of the user.
Tramfloc®
1110 ANTIFOAM and DEFOAMER
Return To Listing
Technical Information Bulletin
Tramfloc® 1111 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc® 1111 is an excellent ANTIFOAM
and DEFOAMER emulsion based upon a unique organic/polysiloxane
compound. It is used for controlling foam in aqueous
systems. Tramfloc® 1111 is compatible
in most systems where foaming is a problem. It may
be used in hot foaming systems {up to 180oF} and
remain stable. Tramfloc® 1111 is
stable in acid, alkaline, or neutral systems. It
is compatible with foaming systems common to agrichemicals,
coatings, chemical processing, carpet dyeing, industrial
cleaners, and water treatments.
TYPICAL PROPERTIES
Appearance: Milky, White Liquid
Specific Gravity @ 20°C: 1.00
Viscosity {20oC}: 1,000-3,500 cps
Defoamer Actives: 15
pH: 6-8
USES
Use levels of Tramfloc® 1111 depend
upon the nature and severity of the foaming. Normally
in latex systems, it should be evaluated initially
as a pound for pound replacement for conventional
defoamers. Dilutions of Tramfloc®
1111 should be made by first charging the water
and then adding Tramfloc® 1111.
Mechanical mixing is required to insure even distribution.
Water dilutions below 5% may have limited shelf
stability.
EPA
STATUS
The ingredients of Tramfloc ® 1111
are listed in EPA Regulations, 40 CFR 180.1001(d)
{exempted from the requirements of a tolerance for
application on growing crops}.
STORAGE
Tramfloc ® 1111 should remain shelf
stable for up to 12 months in its original, sealed
container. To avoid freezing, store above 40oF.
Product may separate upon freezing.
The above data is based upon information Tramfloc
® , Inc. believes reliable and is supplied
for informational purposes only. Tramfloc ®
, Inc. disclaims any liability for damage
or injury which results from the use of the above
data and nothing contained herein shall constitute
a guarantee, warranty (including warranty of merchantability
or fitness for a particular purpose) or representation
(including freedom from patent liability) by Tramfloc
® , Inc. with respect to the accuracy
or completeness of the data, the product described,
or their use for any specific purpose even if that
purpose is known to Tramfloc ® ,
Inc. The final determination of the suitability
of the information, the manner of use of the information
or product and potential infringement of patents
is the sole responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc® 1112 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc ® 1112 ANTIFOAM and DEFOAMER
is a high active, silicone defoamer emulsion dispersible
in warm or cold water. It is a stable emulsion in
acid, alkaline, or neutral systems. It can be added
directly to the foam system.
TYPICAL PROPERTIES
Defoamer Actives: 30%
Color: Off White
Physical Appearance: Pourable, Creamy Liquid
Stability: Greater Than Six Months
Emulsifier: Nonionic
Tramfloc ® 1112 ANTIFOAM and DEFOAMER
is compatible in most wet processing applications,
but it is advisable to pre-check each application.
The small amount required should not introduce any
compatibility problems, even in conditions of strong
electrolytes, etc. Tramfloc ® 1112
ANTIFOAM and DEFOAMER is most effective when used
to prevent foam formulation; therefore, it is best
to add it to the system before foaming starts. Tramfloc
® 1112 ANTIFOAM and DEFOAMER concentration
should be adjusted for each foaming system to determine
the optimum concentration to use. It is suggested
that the concentrations can be decreased to establish
the most economical concentration. Dilutions should
be made by charging the water with Tramfloc
® 1112. Mechanical mixing is required
to ensure even distribution. Water dilutions below
10% may have limited shelf stability. Consult Tramfloc
® , Inc. for dilution procedures.
FDA STATUS
Tramfloc ® 1112 is manufactured
in compliance with the Regulations of the Food and
Drug Administration as cited in 21 CFR, Section
176.210 {paper and paperboard defoamers}.
EPA STATUS
Exceptions from the requirement of a tolerance {40
CFR 180.1001(d)} inert {or occasionally active}
ingredients for use in formulations applied to growing
crops.
STORAGE
Tramfloc ® 1112 has a shelf life
of up to twelve months in its original, unopened
container.
The above data is based upon information Tramfloc
® , Inc. believes reliable and is supplied
for informational purposes only. Tramfloc ®
, Inc. disclaims any liability for damage
or injury which results from the use of the above
data and nothing contained herein shall constitute
a guarantee, warranty (including warranty of merchantability
or fitness for a particular purpose) or representation
(including freedom from patent liability) by Tramfloc
® , Inc. with respect to the accuracy
or completeness of the data, the product described,
or their use for any specific purpose even if that
purpose is known to Tramfloc ® ,
Inc. The final determination of the suitability
of the information, the manner of use of the information
or product and potential infringement of patents
is the sole responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc® 1113 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc ® 1113 ANTIFOAM and DEFOAMER
is a highly active, silicone defoamer emulsion dispersible
in warm or cold water. It is a stable emulsion in
acid, alkaline, or neutral systems. It can be added
directly to the foam system.
TYPICAL PROPERTIES
Defoamer Actives: 33%
Color: Off White
Physical Appearance: Pourable, Creamy Liquid
Stability: Greater Than Six Months
Emulsifier: Non-Ionic
Tramfloc ® 1113 ANTIFOAM and DEFOAMER
is compatible in most wet processing applications,
but it is advisable to pre-check each application.
The small amount required should not introduce any
compatibility problems, even in conditions of strong
electrolytes, etc. Tramfloc ® 1113
ANTIFOAM and DEFOAMER is most effective when used
to prevent foam formulation; therefore, it is best
to add it to the system before foaming starts. Tramfloc
® 1113 ANTIFOAM and DEFOAMER concentration
should be adjusted for each foaming system to determine
the optimum concentration to use. It is suggested
that the concentrations can be decreased to establish
the most economical concentration. Dilutions should
be made by first charging the water and then adding
Tramfloc ® 1113. Mechanical mixing
is required to ensure even distribution. Water dilutions
below 10% may have limited shelf stability. Ask
us for dilution procedures.
FDA STATUS Tramfloc ® 1113 is manufactured
in compliance with the Regulations of the Food and
Drug Administration as cited in 21 CFR, Section
176.210 {paper and paperboard defoamers}.
EPA STATUS Exception from the requirements of a
tolerance {40 CFR 180.1001(d)} inert {or occasionally
active} ingredients for use in formulations applied
to growing crops.
The above data is based upon information Tramfloc
® , Inc. believes reliable and is supplied
for informational purposes only. Tramfloc ®
, Inc. disclaims any liability for damage
or injury which results from the use of the above
data and nothing contained herein shall constitute
a guarantee, warranty (including warranty of merchantability
or fitness for a particular purpose) or representation
(including freedom from patent liability) by Tramfloc
® , Inc. with respect to the accuracy
or completeness of the data, the product described,
or their use for any specific purpose even if that
purpose is known to Tramfloc ® ,
Inc. The final determination of the suitability
of the information, the manner of use of the information
or product and potential infringement of patents
is the sole responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc® 1114 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc ® 1114 Antifoam is an
excellent ANTIFOAM and DEFOAMER emulsion based upon
a unique organic/polysiloxane compound. It is used
for controlling foam in aqueous systems. Tramfloc
® 1114 Antifoam has been designed for
improved shelf life at lower concentrations. It
is compatible in most systems where foaming is a
problem. Tramfloc ® 1114 Antifoam
may be used in hot foaming systems {up to 180°F}
and remain stable. After its use in high temperature
environments, it can be rinsed freely away without
oil scum deposits. Its unique dispersing properties
allow it to be used with most conventional aqueous
systems without "fish-eye" effects. Tramfloc
® 1114 Antifoam is stable in mild acid
or alkaline systems.
TYPICAL PROPERTIES
Appearance: Milky, White Liquid
Specific Gravity @ 20°C: 1.00
Viscosity {20°C}: 1,000-2,000 cps
pH 6-8
FDA STATUS
Tramfloc ® 1114 Antifoam is manufactured
in compliance with the Regulations of the Food and
Drug Administration as cited in 21 CFR, Sections
176.170 and 176.180, for use as a defoamer for coatings
and adhesives that contact food.
STORAGE
Tramfloc ® 1114 Antifoam has a
shelf life of up to 12 months in its original, unopened
container.
The above data is based upon information Tramfloc
® , Inc. believes reliable and is supplied
for informational purposes only. Tramfloc ®
, Inc. disclaims any liability for damage
or injury which results from the use of the above
data and nothing contained herein shall constitute
a guarantee, warranty (including warranty of merchantability
or fitness for a particular purpose) or representation
(including freedom from patent liability) by Tramfloc
® , Inc. with respect to the accuracy
or completeness of the data, the product described,
or their use for any specific purpose even if that
purpose is known to Tramfloc ® ,
Inc. The final determination of the suitability
of the information, the manner of use of the information
or product and potential infringement of patents
is the sole responsibility of the user.
Return To Listing
Technical Information Bulletin
Tramfloc® 1115 ANTIFOAM and DEFOAMER
DESCRIPTION
Tramfloc ® 1115 Antifoam is an
excellent ANTIFOAM and DEFOAMER emulsion based
upon a unique organic/polysiloxane compound. It
is used for controlling foam in aqueous systems.
Tramfloc ® 1115 Antifoam has
been designed for improved shelf life at lower
concentrations. It is compatible in most systems
where foaming is a problem. Tramfloc ®
1115 Antifoam may be used in hot foaming
systems {up to 180°F} and remain stable. After
its use in high temperature environments, it can
be rinsed freely away without oil scum deposits.
Its unique dispersing properties allow it to be
used with most conventional aqueous systems without
"fish-eye" effects. Tramfloc ®
1115 Antifoam is stable in mild acid or alkaline
systems.
TYPICAL PROPERTIES
Appearance: Milky, White Liquid
Specific Gravity @ 20°C: 1.00
Viscosity {20°C}: 1,000-2,000 cps
pH 6-8
FDA STATUS
Tramfloc ® 1115 Antifoam is manufactured
